INFO - PLT FED TTCrx OK (PLL ready, dll ready, frame synced)
WARN - soft FEDID = 32 doesn't match hard board FEDID = 34
WARN - PLT FED #0 warning: base address in config file (0x44000000) does not match address in FED params data file (0x44)
INFO - Set up PLT FED interface #0, base address = 0x44, ID = 32
INFO - Output will be stored in this file: /home/2017ColdBox/cmsplt/interface/calib/pltlevelsfast_calibration_output.txt
WARN - soft FEDID = 32 doesn't match hard board FEDID = 34
INFO - PLTFED channel 0-1 (mFec 7-1 hubAddress 5 roc 1)
INFO -  Levels and [separations]: BLMax: 0 [-nan], 1DC: 0 [-nan], 2DC: 0 [-nan], 3DC: 0
INFO - PLTFED channel 0-2 (mFec 7-1 hubAddress 5 roc 2)
INFO -  Levels and [separations]: BLMax: 0 [-nan], 1DC: 0 [-nan], 2DC: 0 [-nan], 3DC: 0
INFO - PLTFED channel 0-3 (mFec 7-1 hubAddress 5 roc 3)
INFO -  Levels and [separations]: BLMax: 0 [-nan], 1DC: 0 [-nan], 2DC: 0 [-nan], 3DC: 0
INFO - PLTFED channel 0-4 (mFec 7-1 hubAddress 13 roc 1)
INFO -  Levels and [separations]: BLMax: 0 [-nan], 1DC: 0 [-nan], 2DC: 0 [-nan], 3DC: 0
INFO - PLTFED channel 0-5 (mFec 7-1 hubAddress 13 roc 2)
INFO -  Levels and [separations]: BLMax: 0 [-nan], 1DC: 0 [-nan], 2DC: 0 [-nan], 3DC: 0
INFO - PLTFED channel 0-6 (mFec 7-1 hubAddress 13 roc 3)
INFO -  Levels and [separations]: BLMax: 0 [-nan], 1DC: 0 [-nan], 2DC: 0 [-nan], 3DC: 0
INFO - PLTFED channel 0-10 (mFec 7-1 hubAddress 21 roc 1)
INFO -  Levels and [separations]: BLMax: 0 [-nan], 1DC: 0 [-nan], 2DC: 0 [-nan], 3DC: 0
INFO - PLTFED channel 0-11 (mFec 7-1 hubAddress 21 roc 2)
INFO -  Levels and [separations]: BLMax: 0 [-nan], 1DC: 0 [-nan], 2DC: 0 [-nan], 3DC: 0
INFO - PLTFED channel 0-12 (mFec 7-1 hubAddress 21 roc 3)
INFO -  Levels and [separations]: BLMax: 0 [-nan], 1DC: 0 [-nan], 2DC: 0 [-nan], 3DC: 0
INFO - PLTFED channel 0-13 (mFec 7-1 hubAddress 29 roc 1)
INFO -  Levels and [separations]: BLMax: 0 [-nan], 1DC: 0 [-nan], 2DC: 0 [-nan], 3DC: 0
INFO - PLTFED channel 0-14 (mFec 7-1 hubAddress 29 roc 2)
INFO -  Levels and [separations]: BLMax: 202.938 [41.2092], 1DC: 299.125 [59.8681], 2DC: 528.167 [97.0408], 3DC: 1011.02
INFO - PLTFED channel 0-15 (mFec 7-1 hubAddress 29 roc 3)
INFO -  Levels and [separations]: BLMax: 199.062 [34.4504], 1DC: 277.604 [66.8299], 2DC: 470.104 [245.452], 3DC: 1023
INFO - Beginning fine timing calibration...
WARN - soft FEDID = 32 doesn't match hard board FEDID = 34
ERROR - Error: ot all fastors are landing in the same bucket.  Either that or there are no fastors!!!
INFO - MaxBucket after adjustment for pltFedId 0 pltFedChannel  1: 1000
INFO - MaxBucket after adjustment for pltFedId 0 pltFedChannel  2: 1000
INFO - MaxBucket after adjustment for pltFedId 0 pltFedChannel  3: 1000
INFO - MaxBucket after adjustment for pltFedId 0 pltFedChannel  4: 1000
INFO - MaxBucket after adjustment for pltFedId 0 pltFedChannel  5: 1000
INFO - MaxBucket after adjustment for pltFedId 0 pltFedChannel  6: 1000
INFO - MaxBucket after adjustment for pltFedId 0 pltFedChannel 10: 1000
INFO - MaxBucket after adjustment for pltFedId 0 pltFedChannel 11: 1000
INFO - MaxBucket after adjustment for pltFedId 0 pltFedChannel 12: 1000
INFO - MaxBucket after adjustment for pltFedId 0 pltFedChannel 13: 1000
INFO - MaxBucket after adjustment for pltFedId 0 pltFedChannel 14: 10
INFO - MaxBucket after adjustment for pltFedId 0 pltFedChannel 15: 10
WARN - Something looks not quite right so: writing params files to calib/
WARN - If you want these settings you have to copy them by hand
ERROR: couldn't find conf/params_pltfed32.dat; perhaps the calibration failed? Files will not be moved.
ERROR: pltfed1_id is not set in calibration-configuration.conf; file will not be moved