INFO - PLT FED TTCrx OK (PLL ready, dll ready, frame synced)
WARN - soft FEDID = 32 doesn't match hard board FEDID = 34
WARN - PLT FED #0 warning: base address in config file (0x44000000) does not match address in FED params data file (0x44)
INFO - Set up PLT FED interface #0, base address = 0x44, ID = 32
INFO - Output will be stored in this file: /home/2017ColdBox/cmsplt/interface/calib/pltlevelsfast_calibration_output.txt
WARN - soft FEDID = 32 doesn't match hard board FEDID = 34
INFO - PLTFED channel 0-1 (mFec 7-1 hubAddress 5 roc 1)
INFO -  Levels and [separations]: BLMax: 85.9792 [23.3824], 1DC: 140.688 [35.5158], 2DC: 244.271 [32.0771], 3DC: 458.042
INFO - PLTFED channel 0-2 (mFec 7-1 hubAddress 5 roc 2)
INFO -  Levels and [separations]: BLMax: 105.875 [29.8926], 1DC: 155.729 [39.2893], 2DC: 252.333 [32.0362], 3DC: 473.604
INFO - PLTFED channel 0-3 (mFec 7-1 hubAddress 5 roc 3)
INFO -  Levels and [separations]: BLMax: 28.7708 [-0.0674472], 1DC: 28.625 [-0.575935], 2DC: 27.1042 [-0.228882], 3DC: 26.4792
INFO - PLTFED channel 0-4 (mFec 7-1 hubAddress 13 roc 1)
INFO -  Levels and [separations]: BLMax: 0 [-nan], 1DC: 0 [-nan], 2DC: 0 [-nan], 3DC: 0
INFO - PLTFED channel 0-5 (mFec 7-1 hubAddress 13 roc 2)
INFO -  Levels and [separations]: BLMax: 0 [-nan], 1DC: 0 [-nan], 2DC: 0 [-nan], 3DC: 0
INFO - PLTFED channel 0-6 (mFec 7-1 hubAddress 13 roc 3)
INFO -  Levels and [separations]: BLMax: 0 [-nan], 1DC: 0 [-nan], 2DC: 0 [-nan], 3DC: 0
INFO - PLTFED channel 0-10 (mFec 7-1 hubAddress 21 roc 1)
INFO -  Levels and [separations]: BLMax: 0 [-nan], 1DC: 0 [-nan], 2DC: 0 [-nan], 3DC: 0
INFO - PLTFED channel 0-11 (mFec 7-1 hubAddress 21 roc 2)
INFO -  Levels and [separations]: BLMax: 0 [-nan], 1DC: 0 [-nan], 2DC: 0 [-nan], 3DC: 0
INFO - PLTFED channel 0-12 (mFec 7-1 hubAddress 21 roc 3)
INFO -  Levels and [separations]: BLMax: 0 [-nan], 1DC: 0 [-nan], 2DC: 0 [-nan], 3DC: 0
INFO - PLTFED channel 0-13 (mFec 7-1 hubAddress 29 roc 1)
INFO -  Levels and [separations]: BLMax: 0 [-nan], 1DC: 0 [-nan], 2DC: 0 [-nan], 3DC: 0
INFO - PLTFED channel 0-14 (mFec 7-1 hubAddress 29 roc 2)
INFO -  Levels and [separations]: BLMax: 0 [-nan], 1DC: 0 [-nan], 2DC: 0 [-nan], 3DC: 0
INFO - PLTFED channel 0-15 (mFec 7-1 hubAddress 29 roc 3)
INFO -  Levels and [separations]: BLMax: 212.271 [40], 1DC: 301.896 [73.556], 2DC: 575.75 [115.008], 3DC: 1022.06
INFO - Beginning fine timing calibration...
WARN - WARNING: bmax - bmin > 3
ERROR - Cannot find the right bucket for PLT FED channel 0-1: Adjust = 7
ERROR - Cannot find the right bucket for PLT FED channel 0-2: Adjust = 6
ERROR - Cannot find the right bucket for PLT FED channel 0-15: Adjust = 7
WARN - soft FEDID = 32 doesn't match hard board FEDID = 34
ERROR - Error: ot all fastors are landing in the same bucket.  Either that or there are no fastors!!!
INFO - MaxBucket after adjustment for pltFedId 0 pltFedChannel  1: 8
INFO - MaxBucket after adjustment for pltFedId 0 pltFedChannel  2: 9
INFO - MaxBucket after adjustment for pltFedId 0 pltFedChannel  3: 12
INFO - MaxBucket after adjustment for pltFedId 0 pltFedChannel  4: 1000
INFO - MaxBucket after adjustment for pltFedId 0 pltFedChannel  5: 1000
INFO - MaxBucket after adjustment for pltFedId 0 pltFedChannel  6: 1000
INFO - MaxBucket after adjustment for pltFedId 0 pltFedChannel 10: 1000
INFO - MaxBucket after adjustment for pltFedId 0 pltFedChannel 11: 1000
INFO - MaxBucket after adjustment for pltFedId 0 pltFedChannel 12: 1000
INFO - MaxBucket after adjustment for pltFedId 0 pltFedChannel 13: 1000
INFO - MaxBucket after adjustment for pltFedId 0 pltFedChannel 14: 1000
INFO - MaxBucket after adjustment for pltFedId 0 pltFedChannel 15: 8
WARN - Something looks not quite right so: writing params files to calib/
WARN - If you want these settings you have to copy them by hand
ERROR: couldn't find conf/params_pltfed32.dat; perhaps the calibration failed? Files will not be moved.
ERROR: pltfed1_id is not set in calibration-configuration.conf; file will not be moved