INFO - PLT FED TTCrx OK (PLL ready, dll ready, frame synced)
WARN - soft FEDID = 32 doesn't match hard board FEDID = 34
WARN - PLT FED #0 warning: base address in config file (0x44000000) does not match address in FED params data file (0x44)
INFO - Set up PLT FED interface #0, base address = 0x44, ID = 32
INFO - Output will be stored in this file: /home/2017ColdBox/cmsplt/interface/calib/pltlevelsfast_calibration_output.txt
WARN - soft FEDID = 32 doesn't match hard board FEDID = 34
INFO - PLTFED channel 0-1 (mFec 7-1 hubAddress 5 roc 1)
INFO -  Levels and [separations]: BLMax: 161.958 [15.9535], 1DC: 217.062 [32.1076], 2DC: 345.646 [74.8345], 3DC: 708.375
INFO - PLTFED channel 0-2 (mFec 7-1 hubAddress 5 roc 2)
INFO -  Levels and [separations]: BLMax: 172.417 [26.2435], 1DC: 224.854 [56.3087], 2DC: 338.354 [178.378], 3DC: 787.104
INFO - PLTFED channel 0-3 (mFec 7-1 hubAddress 5 roc 3)
INFO -  Levels and [separations]: BLMax: 115.354 [13.6699], 1DC: 151.271 [21.4476], 2DC: 201.938 [178.252], 3DC: 708.646
INFO - PLTFED channel 0-4 (mFec 7-1 hubAddress 13 roc 1)
INFO -  Levels and [separations]: BLMax: 145.979 [43.9558], 1DC: 243 [58.0415], 2DC: 494.146 [132.924], 3DC: 1023
INFO - Threshold 0 for 0-4 manually adjusted to 230
INFO - PLTFED channel 0-5 (mFec 7-1 hubAddress 13 roc 2)
INFO -  Levels and [separations]: BLMax: 214.688 [33.1867], 1DC: 289.833 [46.0943], 2DC: 476 [36.0058], 3DC: 1000.9
INFO - PLTFED channel 0-6 (mFec 7-1 hubAddress 13 roc 3)
INFO -  Levels and [separations]: BLMax: 178.312 [33.4305], 1DC: 257.562 [44.9925], 2DC: 461.167 [134.29], 3DC: 1023
INFO - PLTFED channel 0-10 (mFec 7-1 hubAddress 21 roc 1)
INFO -  Levels and [separations]: BLMax: 124.292 [37.0767], 1DC: 217.688 [57.0395], 2DC: 451.188 [158.812], 3DC: 1023
INFO - PLTFED channel 0-11 (mFec 7-1 hubAddress 21 roc 2)
INFO -  Levels and [separations]: BLMax: 160.312 [60.2501], 1DC: 303.708 [80.4636], 2DC: 658.521 [91.9813], 3DC: 1023
INFO - PLTFED channel 0-12 (mFec 7-1 hubAddress 21 roc 3)
INFO -  Levels and [separations]: BLMax: 253.958 [56.0982], 1DC: 381.312 [76.0039], 2DC: 715.25 [76.683], 3DC: 1023
INFO - PLTFED channel 0-13 (mFec 7-1 hubAddress 29 roc 1)
INFO -  Levels and [separations]: BLMax: 138.958 [36.3627], 1DC: 222.458 [34.1562], 2DC: 421.771 [24.9746], 3DC: 899.771
INFO - PLTFED channel 0-14 (mFec 7-1 hubAddress 29 roc 2)
INFO -  Levels and [separations]: BLMax: 240.75 [39.6365], 1DC: 327.854 [71.9214], 2DC: 574.062 [149.679], 3DC: 1023
INFO - PLTFED channel 0-15 (mFec 7-1 hubAddress 29 roc 3)
INFO -  Levels and [separations]: BLMax: 0 [-nan], 1DC: 0 [-nan], 2DC: 0 [-nan], 3DC: 0
INFO - Beginning fine timing calibration...
WARN - soft FEDID = 32 doesn't match hard board FEDID = 34
ERROR - Error: ot all fastors are landing in the same bucket.  Either that or there are no fastors!!!
INFO - MaxBucket after adjustment for pltFedId 0 pltFedChannel  1: 9
INFO - MaxBucket after adjustment for pltFedId 0 pltFedChannel  2: 9
INFO - MaxBucket after adjustment for pltFedId 0 pltFedChannel  3: 9
INFO - MaxBucket after adjustment for pltFedId 0 pltFedChannel  4: 9
INFO - MaxBucket after adjustment for pltFedId 0 pltFedChannel  5: 9
INFO - MaxBucket after adjustment for pltFedId 0 pltFedChannel  6: 9
INFO - MaxBucket after adjustment for pltFedId 0 pltFedChannel 10: 9
INFO - MaxBucket after adjustment for pltFedId 0 pltFedChannel 11: 9
INFO - MaxBucket after adjustment for pltFedId 0 pltFedChannel 12: 9
INFO - MaxBucket after adjustment for pltFedId 0 pltFedChannel 13: 9
INFO - MaxBucket after adjustment for pltFedId 0 pltFedChannel 14: 9
INFO - MaxBucket after adjustment for pltFedId 0 pltFedChannel 15: 1000
WARN - Something looks not quite right so: writing params files to calib/
WARN - If you want these settings you have to copy them by hand
ERROR: couldn't find conf/params_pltfed32.dat; perhaps the calibration failed? Files will not be moved.
ERROR: pltfed1_id is not set in calibration-configuration.conf; file will not be moved