INFO - PLT FED TTCrx OK (PLL ready, dll ready, frame synced)
WARN - soft FEDID = 32 doesn't match hard board FEDID = 34
WARN - PLT FED #0 warning: base address in config file (0x44000000) does not match address in FED params data file (0x44)
INFO - Set up PLT FED interface #0, base address = 0x44, ID = 32
INFO - Output will be stored in this file: /home/2017ColdBox/cmsplt/interface/calib/pltlevelsfast_calibration_output.txt
WARN - soft FEDID = 32 doesn't match hard board FEDID = 34
INFO - PLTFED channel 0-1 (mFec 7-1 hubAddress 5 roc 1)
INFO -  Levels and [separations]: BLMax: 171.521 [18.194], 1DC: 210.521 [49.4678], 2DC: 322.125 [176.038], 3DC: 744.25
INFO - PLTFED channel 0-2 (mFec 7-1 hubAddress 5 roc 2)
INFO -  Levels and [separations]: BLMax: 188.958 [15.8115], 1DC: 233.417 [32.8152], 2DC: 338.458 [131.754], 3DC: 931.188
INFO - PLTFED channel 0-3 (mFec 7-1 hubAddress 5 roc 3)
INFO -  Levels and [separations]: BLMax: 140.271 [22.3483], 1DC: 204.396 [48.0372], 2DC: 383.333 [213.813], 3DC: 1023
INFO - PLTFED channel 0-4 (mFec 7-1 hubAddress 13 roc 1)
INFO -  Levels and [separations]: BLMax: 186.604 [19.1956], 1DC: 261.104 [28.4917], 2DC: 458.104 [89.9304], 3DC: 1023
INFO - Threshold 0 for 0-4 manually adjusted to 230
INFO - PLTFED channel 0-5 (mFec 7-1 hubAddress 13 roc 2)
INFO -  Levels and [separations]: BLMax: 187.292 [21.0195], 1DC: 236.146 [30.7294], 2DC: 360.625 [17.6962], 3DC: 809.75
INFO - PLTFED channel 0-6 (mFec 7-1 hubAddress 13 roc 3)
INFO -  Levels and [separations]: BLMax: 146.208 [21.9939], 1DC: 192.458 [24.364], 2DC: 311.583 [19.1341], 3DC: 766.521
INFO - PLTFED channel 0-10 (mFec 7-1 hubAddress 21 roc 1)
INFO -  Levels and [separations]: BLMax: 158.729 [18.1157], 1DC: 229.208 [39.3795], 2DC: 408.312 [179.313], 3DC: 1023
INFO - PLTFED channel 0-11 (mFec 7-1 hubAddress 21 roc 2)
INFO -  Levels and [separations]: BLMax: 182.729 [36.7051], 1DC: 294.958 [62.2601], 2DC: 596.146 [100.97], 3DC: 1023
INFO - PLTFED channel 0-12 (mFec 7-1 hubAddress 21 roc 3)
INFO -  Levels and [separations]: BLMax: 228.417 [31.3617], 1DC: 333.167 [49.7428], 2DC: 633.375 [73.5415], 3DC: 1023
INFO - PLTFED channel 0-13 (mFec 7-1 hubAddress 29 roc 1)
INFO -  Levels and [separations]: BLMax: 168.562 [18.6984], 1DC: 219.646 [18.3905], 2DC: 339.896 [16.206], 3DC: 715.542
INFO - PLTFED channel 0-14 (mFec 7-1 hubAddress 29 roc 2)
INFO -  Levels and [separations]: BLMax: 194.042 [23.7626], 1DC: 259.792 [51.4749], 2DC: 467.562 [160.368], 3DC: 1023
INFO - PLTFED channel 0-15 (mFec 7-1 hubAddress 29 roc 3)
INFO -  Levels and [separations]: BLMax: 0 [-nan], 1DC: 0 [-nan], 2DC: 0 [-nan], 3DC: 0
INFO - Beginning fine timing calibration...
WARN - soft FEDID = 32 doesn't match hard board FEDID = 34
ERROR - Error: ot all fastors are landing in the same bucket.  Either that or there are no fastors!!!
INFO - MaxBucket after adjustment for pltFedId 0 pltFedChannel  1: 9
INFO - MaxBucket after adjustment for pltFedId 0 pltFedChannel  2: 9
INFO - MaxBucket after adjustment for pltFedId 0 pltFedChannel  3: 9
INFO - MaxBucket after adjustment for pltFedId 0 pltFedChannel  4: 9
INFO - MaxBucket after adjustment for pltFedId 0 pltFedChannel  5: 9
INFO - MaxBucket after adjustment for pltFedId 0 pltFedChannel  6: 9
INFO - MaxBucket after adjustment for pltFedId 0 pltFedChannel 10: 9
INFO - MaxBucket after adjustment for pltFedId 0 pltFedChannel 11: 9
INFO - MaxBucket after adjustment for pltFedId 0 pltFedChannel 12: 9
INFO - MaxBucket after adjustment for pltFedId 0 pltFedChannel 13: 9
INFO - MaxBucket after adjustment for pltFedId 0 pltFedChannel 14: 9
INFO - MaxBucket after adjustment for pltFedId 0 pltFedChannel 15: 1000
WARN - Something looks not quite right so: writing params files to calib/
WARN - If you want these settings you have to copy them by hand
ERROR: couldn't find conf/params_pltfed32.dat; perhaps the calibration failed? Files will not be moved.
ERROR: pltfed1_id is not set in calibration-configuration.conf; file will not be moved